How can I order on size 8 US? View answer
Asked 5 ´years ago
Will this work with 3/16" synthetic winch line? View answer
Asked 7 ´years ago | 1-1/8" Nylon Chafe Sleeve
What is the hook size on this assembly? View answer
Asked 5 ´years ago
I HAVE AN OLDER 17T CROSBY SHACKLE THAT'S MISSING THE xxxx PIN OR CROSS BOLT (not sure which it takes? MY SHACKLE IS NOT SHAPED EXACTLY LIKE THE ONE PICTURED. MY SHACKLE IS SHAPED LIKE THE LETTER U. MY SHACKLE IS 9" LONG AND 5 &1/2" WIDE. IS THIS SOMETHING YOU HAVE IN STOCK OR CAN SPECIAL ORDER FOR ME? ANY HELP WILL BE GREATLY APPRECIATED. View answer
Asked 4 ´years ago | Crosby 1-1/2" G-2130 Bolt Type Anchor Shackle - 17 Ton WLL - #1019631
Why is the pin painted orange? View answer
Asked 7 ´years ago
Asked 5 ´years ago | Viking Orange Rubber Calk Chainsaw Boots
What do you torque these to and how much weight will they hold using two on the end of 3/8" wire rope? Also how much dead end cable do you suggest for clamping 3/8" wire rope? I want to use two on both ends of my cables which will all be about 8ft long. View answer
Asked 5 ´years ago | Crosby 3/8" G-450 Wire Rope Clip - #1010097
How about if using 5/8 line to hang it? View answer
Asked 5 ´years ago | ISC RP048 Compact Arborist Rigging Block
What is the country of origin? Where is it made? View answer
Asked 4 ´years ago
Is the stated weight of 5.65lbs for 2 feet of the Abus 12KS 1/2" (12mm) chain correct? This works out to be 2.825lbs per foot.On your listing for 10 feet of the Abus 12KS 1/2" (12mm) chain, you have a stated weight of 21.5lbs, which works out to be 2.15lbs per foot. View answer
Asked 6 ´years ago | Abus 12KS 1/2" (12mm) x 2 ft Security Chain w/ Sleeve
How do you lubricate the locking components of this mechanism? View answer
Asked 7 ´years ago
We have an enclosed trailer that was modified to haul classic cars. The rear ramp, modified with steel and 3/4 plywood, weighing about 800 lbs., is raised and lowered by a 2500 lb. winch. 5/16 cable runs over a 2" pulley suspended at the ceiling, just inside the door. After only about 20 open/close cycles, at a point EXACTLY 10 inches up from the thimble where cable attaches to the ramp, the "core" stand of the cable begins to protrude about a 1/2 inch. I tried steel, stainless, and galvanized; always happens in the same spot, same time frame! Any ideas why? I've cut 16" off the end, replace thimble and clamps, and it happens again! View answer
Asked 4 ´years ago | 5/16" 7x19 Stainless Steel Aircraft Cable - 9000 lbs Breaking Strength
Looking for 5000 pieces View answer
Asked 7 ´years ago | 1/8" Copper Swage Stop
When will these be back in stock? View answer
Asked 5 ´years ago | Fusion Z-Max Hyper Speed Handle Bar Trolley
Do you have women's sizes? View answer
Asked 6 ´years ago | Red Steer Chilly Grip Water-Resistant Thermal Glove
How do I know if these will fit my climbers? View answer
Asked 5 ´years ago | Klein Replacement Tree Gaffs - #07