Question 1

I already have a few of these but I just lost the pin on one of them. Is it possible to purchase that piece only? View answer

Asked 4 ´years ago | Crosby 1/4" G-209 Screw Pin Anchor Shackle - 1/2 Ton WLL - #1018375

Question 2

Do you have two of the Crosby 1013584 in-stock? View answer

Asked 6 ´years ago | Crosby 5/8" A-341 Alloy Pear Link - 9000 lbs WLL - #1013584

Question 3

Can you provide material certification sheets for this item from Crosby? View answer

Asked 5 ´years ago | Crosby L-322AN 15 Ton Alloy Swivel Hook w/ Latch - #1048880

Question 4

Do you have a replacement nub as shown in the photo below. 1/2" wire rope. Only need nub and mounting hardware. View answer

Asked 6 ´years ago | 1/2" MEDIUM DUTY Cat Choker w/ Eye

Question 5

Do these boots work well in the rigging? Can I get around the brush in them or are they made more for cutters? View answer

Asked 6 ´years ago

Question 6

Saw a vid of cutting both sides of a Pewag 12mm in about 130 seconds with an angle grinder and another of cutting same chain in about 55 seconds with a die grinder. Being through hardened, would this chain give more resistance to a grinder? View answer

Asked 7 ´years ago

Question 7

I am looking to purchase 2 coated cables 3/8" by 20 ft long with loops at both ends. Can you provide such a product? View answer

Asked 7 ´years ago | 3/8" x 26 ft Log Truck Wrapper w/ 8 ft of 5/16" G70 Chain

Question 8

Will this fit an ARS EXW 2.7 pole saw? How fr apart are the xxxx holes on this blade? View answer

Asked 6 ´years ago | Samurai Ichigeki 13" Replacement Blade

Question 9

What color is this? View answer

Asked 7 ´years ago | CRC Zinc-It Cold Galvanizing Spray - 16 oz

Question 10

Is it heat resistant? View answer

Asked 6 ´years ago | Pelican 1/2" x 48" Double Braid Prusik & Snap Hook

Question 11

Can the spring and pin, just be purchased? View answer

Asked 3 ´years ago | Crosby S-4316 5/8" Shur-Loc Latch Kit - #6603014

Question 12

is the MSA-815362 GMA-P100 out of stock? View answer

Asked 5 ´years ago | MSA Advantage Respirator Cartridge GMA-P100 2-Pack - #815362

Question 13

What is the overall length of this turnbuckle when taken up all the way as in the photo above? View answer

Asked 5 ´years ago | 5/8" x 6" Forged Jaw & Jaw Turnbuckle - 3500 lbs WLL

Question 14

What's the inside diameter of the ring? View answer

Asked 4 ´years ago | USR Large Stainless Steel Ring

Question 15

Is the pitch on this metric bolt 1.5? View answer

Asked 2 ´years ago | Chicago M14 x 44.5 Metric Machinery Eye Bolt - 1600 kg WLL

Question 16

Where are these made? View answer

Asked 5 ´years ago | HIT Replacement Blades for 24" Black Head Bolt Cutters - #22-BC24B

Question 17

How does it stay on? Does it come with strap? View answer

Asked 5 ´years ago | Forester Leather Shoulder Pad

Question 18

Where can I purchase a replacement pully for my 1-1/4 Marvin pruner head ? View answer

Asked 6 ´years ago | Notch Pruner Head to 1-1/4"

Question 19

What is the torque specification of this hoist ring?  It will be threaded into plastic injection mold, material is P-20 tool steel. View answer

Asked 6 ´years ago | ADB 2"-4-1/2 x 2.96" (SN) Swivel Hoist Ring - 30000 lbs WLL

Question 20

Will this cutter cut, Steel, Chain, 5/16, Grade 8, Spectrum 8 Only View answer

Asked 6 ´years ago

Question 21

What is the WLL on this product? View answer

Asked 6 ´years ago | All Gear 5/8" Husky Bull Rope | 19500 lbs Breaking Strength

Question 22

i am a farmer and i skid wood out of the bush with my 3 pt hitch winch. i run a steel cable now , i find it heavy to roll out and pull it to the tree.would you recommend your rope YC-UWL038X150 and is that what its used for. View answer

Asked 7 ´years ago | 3/8" x 150 ft HMPE Synthetic Winch Line - 17600 lbs Breaking Strength

Question 23

Are these swivels used for side mount picking? View answer

Asked 7 ´years ago | ADB 3/4"-10 x 1.03" Swivel Hoist Ring - 5000 lbs WLL

Question 24

What is the overall diameter of the link? View answer

Asked 8 ´years ago | Peerless 7/16" (11mm) Hex Security Chain Kit - 20 ft Chain & Padlock

Question 25

Will this hold a 12 inch wedge? View answer

Asked 4 ´years ago | Weaver Leather Heavy-Duty Chainsaw Tool & Wedge Pouch

Question 26

Can this turnbuckle be used for overhead lifting? View answer

Asked 5 ´years ago | Crosby 1" x 12" HG-226 Eye & Eye Turnbuckle - 10000 lbs WLL - #1031573

Question 27

What is the current nut size on these? View answer

Asked 2 ´years ago | Suncor 1/4" Type 316 Stainless Steel Wire Rope Clip

Question 28

What is the recommended brand and size saw for this winch? View answer

Asked 5 ´years ago

Question 29

I need some eye nuts to fit a 7/16" bolt.  I assume it is a standard thread, but what is the thread count on this eye nut? View answer

Asked 6 ´years ago | Chicago 7/16" Tap Regular Eye Nut - 1700 lbs WLL

Question 30

WHAT IS THE BORE SIZE OF THIS SHEAVE? WILL A 1-1/2" STEEL ROD FIT THROUGH IT? View answer

Asked 3 ´years ago | Crosby 1193 8" Sheave for 5/8" Wire Rope - #913346

Question 31

Are these imported tongs? If so, where are they imported from? View answer

Asked 7 ´years ago | Dixie Skidding Timber Tongs - 1" x 25" - #40225

Question 32

Can you get this item with a 1 inch wide jaw ? I need a turnbuckle that is no longer than eleven inches closed that will go over a one inch wide d ring and hold minimum of 500 lbs safe load that is made in america that i can get load test certs with. View answer

Asked 5 ´years ago | Chicago 1/2" x 2" Forged Jaw & Jaw Turnbuckle - 2200 lbs WLL

Question 33

What is the recommended tightening torque for the 1016624? View answer

Asked 5 ´years ago | Crosby M12-1.75 x 16.90 mm HR-125M Swivel Hoist Ring - 1050 kg WLL - #1016624

Question 34

Is the steel head, along with the handle, made in the USA? View answer

Asked 6 ´years ago

Question 35

So I need a choker that I can quickly attach to hook on skid loader and the other end to choke the dead sows to pull them out of our farrowing and gestation barns. Ropes are a pain, chains are also. A wire rope choker sling seems like it be the ticket...but will the wire rope quickly break being drug across gravel for short distances...one of the guys worries about getting cut by broken strands of wire...? View answer

Asked 7 ´years ago | 3/8" x 12 ft Cat Choker w/ Eye - 11000 lbs Breaking Strength

Question 36

This product is listed as a chain cutter. How is that different from a bolt cutter? I am considering this as well as your 36" bolt cutter. How are they different? Thank you for your attention to this matter. View answer

Asked 4 ´years ago | HIT 42" Heavy-Duty Chain Cutter - 1/2" Max Cut - #22-CC42P

Question 37

Does the hoist hand pull chain also reach 20ft from the hoist? View answer

Asked 6 ´years ago

Question 38

How hard of ground can I drive this anchor into? I have a lot of shale. View answer

Asked 8 ´years ago | Duckbill 88-DB1 1/4" x 3.5 ft Earth Anchor - 3000 lbs Capacity

Question 39

Are certs available for this item? View answer

Asked 4 ´years ago | Crosby 5/8"-11 x 0.78" SS-125UNC Stainless Steel Swivel Hoist Ring - 2000 lbs WLL - #1065028

Question 40

Is this USA made or other? View answer

Asked 5 ´years ago | 1/2" Forged D-Ring & Weld-on Clip - 4000 lbs WLL

Question 41

Do you have non-galvanized turnbuckle bodies in this size? View answer

Asked 5 ´years ago | Chicago 5/8" x 9" Forged Turnbuckle Body Only - 3500 lbs WLL

Question 42

Can I get a sling like this, except with three legs instead of two? View answer

Asked 2 ´years ago | all-Grip 2 Ply 1" x 4 ft Hi-Vis Polyester DOS 2-Leg Web Sling Bridle - 5,370 lbs WLL @ 60°

Question 43

How do they work? View answer

Asked 4 ´years ago | 3/8" x 15 ft Cat Choker w/ Eye - 11000 lbs Breaking Strength

Question 44

Crosby version has a derating to place the load on the tip of the hook. Do you have a derating value if the load is a certain distance from the hook? View answer

Asked 5 ´years ago | Cartec 7/32" Grade 100 Eye Foundry Hook - 3000 lbs WLL

Question 45

Is it possible to crimp the sides down with pliers or other hand tools? View answer

Asked 6 ´years ago | USR 1/16" x 0.260" Zinc-Plated Stake Eye

Question 46

How much 1/4" cable will it hold? View answer

Asked 4 ´years ago | Thern M4312 Spur Gear Hand Winch - 2000 lbs Pulling Capacity

Question 47

Is the Crosby Grade 100 “Platinum Color” a galvanized finish, or is it just paint that has a galvanized appearance? View answer

Asked 2 ´years ago | Crosby 9/32" (1/4") S-1325A Grade 100 Chain Coupler - 4300 lbs WLL - #1098500

Question 48

What is the actual diameter of the clevis pin on this item? View answer

Asked 2 ´years ago | Crosby 5/16" S-1325A Grade 100 Chain Coupler - 5700 lbs WLL - #1098504

Question 49

What type of lock system is used for rotational lock? View answer

Asked 8 ´years ago

Question 50

Does the chap pants come with the belt and suspenders? If not where can I purchase them and what's the cost View answer

Asked 6 ´years ago

Browse by Topic

Tools